Copper
High electrical and thermal conductivity for busbars, windings and heat exchangers.
Product Overview
Non-Ferrous Metals Stockist and Supplier
We are importers, exporters, stockists and suppliers of copper, brass, aluminium, bronze, gunmetal, zinc and lead in the form of bars, wire, PVC coated copper coil, coils, rounds, sheets, plates, channels, angles and pipes.
Non-ferrous material supports electrical, marine, heat transfer and machining work, where conductivity, corrosion resistance or machinability matter most.
- Copper, brass and aluminium
- Bronze, gunmetal, zinc and lead
- PVC coated copper coil
- Rounds, sections, sheets and tubes
MetalsCu, Brass, Al, Bronze
AlsoGunmetal, Zinc, Lead
FormsBar, Wire, Sheet, Tube
SectionsChannel, Angle, Flat
Non-Ferrous Metals Specifications
- Metals
- Copper, Brass, Aluminium, Bronze, Gunmetal, Zinc, Lead
- Copper Forms
- Round, Hexagonal, Square, Rod, Tube, Sheet, Strip, Foil, Busbar, Plate, Flat, Wire, Tubing, Section, Bush
- Brass Forms
- Round, Hexagonal, Square, Rod, Tube, Sheet, Strip, Foil, Busbar, Plate, Flat, Wire, Tubing, Section, Bush
- Aluminium Forms
- Round, Hexagonal, Square, Rod, Tube, Sheet, Strip, Foil, Busbar, Plate, Flat, Wire, Tubing, Section, Bush
- Other Supply
- PVC Coated Copper Coil, Coils, Channels, Angles, Pipes
Non-Ferrous Metals Grades
Copper
- Electrolytic Copper
- Electrolytic Tough Pitch
- Deoxidised Copper
- Arsenical Phosphorised Copper
- General Purpose Commercial Copper
- High Conductivity Copper
Brass
- Free Cutting
- Leaded
- Forging
- Riveting
- Lead Free
- High Tensile
- Naval
- Gilding
- Red
- Low
- Cartridge
- Yellow
- Basis
- Muntz
Aluminium and Bronze
- Aluminium
- Aluminium Bronze
- Aluminium Silicon Bronze
- Manganese Bronze
- Phosphor Bronze
- Gunmetal
Other Metals
- Zinc
- Lead
Materials
Brass
Excellent machinability for fittings, valves and precision turned parts.
Aluminium
Lightweight and corrosion resistant for sheets, sections and conductors.
Bronze
Wear and corrosion resistance for bushes, bearings and marine parts.
Gunmetal
Pressure tight castings and bushes for valves and pumps.
Zinc and Lead
Used for anodes, sheet work, radiation shielding and alloying.
Product Forms
Chemical Composition
Swipe to see all columns
| Alloy | Common Name | Cu | Zn | Sn | Pb | Al | Others |
|---|---|---|---|---|---|---|---|
| Copper | |||||||
| C11000 | Electrolytic Tough Pitch | 99.90 min | - | - | - | - | O 0.04 max |
| C12200 | Deoxidised Copper | 99.90 min | - | - | - | - | P 0.015 - 0.040 |
| Brass | |||||||
| C26000 | Cartridge Brass | 68.5 - 71.5 | Bal | - | 0.07 max | - | Fe 0.05 max |
| C27200 | Yellow Brass | 62.0 - 65.0 | Bal | - | 0.07 max | - | Fe 0.07 max |
| C28000 | Muntz Metal | 59.0 - 63.0 | Bal | - | 0.30 max | - | Fe 0.07 max |
| C36000 | Free Cutting Brass | 60.0 - 63.0 | Bal | - | 2.5 - 3.7 | - | Fe 0.35 max |
| C46400 | Naval Brass | 59.0 - 62.0 | Bal | 0.5 - 1.0 | 0.20 max | - | Fe 0.10 max |
| Bronze and Gunmetal | |||||||
| C51000 | Phosphor Bronze | Bal | 0.30 max | 4.2 - 5.8 | 0.05 max | - | P 0.03 - 0.35 |
| C95400 | Aluminium Bronze | 83.0 min | - | - | - | 10.0 - 11.5 | Fe 3.0 - 5.0 |
| C83600 | Gunmetal (LG2) | 84.0 - 86.0 | 4.0 - 6.0 | 4.0 - 6.0 | 4.0 - 6.0 | - | - |
| Aluminium | |||||||
| 1100 | Commercial Aluminium | 0.05 - 0.20 | 0.10 max | - | - | 99.0 min | - |
| 6061 | Structural Alloy | 0.15 - 0.40 | 0.25 max | - | - | Bal | Mg 0.8 - 1.2, Si 0.4 - 0.8, Cr 0.04 - 0.35 |
Values are for reference, as per the relevant standard. Percentages are maximum unless a range or minimum is shown. Actual values are stated on the mill test certificate.
Mechanical Properties
Swipe to see all columns
| Alloy | Condition | Tensile (MPa) | Yield (MPa) | Elongation (%) |
|---|---|---|---|---|
| Typical Values | ||||
| C11000 | Annealed | 220 | 69 | 45 |
| C12200 | Annealed | 220 | 69 | 45 |
| C26000 | Annealed | 300 | 75 | 65 |
| C27200 | Annealed | 320 | 100 | 60 |
| C28000 | Annealed | 370 | 145 | 45 |
| C36000 | Half Hard | 400 | 310 | 20 |
| C46400 | Annealed | 380 | 170 | 45 |
| C51000 | Annealed | 325 | 130 | 60 |
| C95400 | As Cast | 586 | 241 | 18 |
| C83600 | As Cast | 255 | 117 | 30 |
| 1100 | Annealed | 90 | 35 | 35 |
| 6061 | T6 | 310 | 276 | 12 |
Typical values for reference. Actual properties depend on temper and product form.
Dimension Chart
Round Bar Theoretical Weight (kg/m)
Swipe to see all columns
| Diameter (mm) | Copper | Brass | Aluminium Bronze | Aluminium |
|---|---|---|---|---|
| 6 | 0.253 | 0.240 | 0.215 | 0.076 |
| 8 | 0.449 | 0.427 | 0.382 | 0.136 |
| 10 | 0.702 | 0.668 | 0.597 | 0.212 |
| 12 | 1.011 | 0.961 | 0.860 | 0.305 |
| 16 | 1.797 | 1.709 | 1.528 | 0.543 |
| 20 | 2.809 | 2.670 | 2.388 | 0.848 |
| 25 | 4.388 | 4.172 | 3.731 | 1.325 |
| 30 | 6.319 | 6.008 | 5.372 | 1.909 |
| 40 | 11.234 | 10.681 | 9.550 | 3.393 |
| 50 | 17.554 | 16.690 | 14.923 | 5.301 |
| 60 | 25.277 | 24.033 | 21.488 | 7.634 |
| 75 | 39.496 | 37.552 | 33.576 | 11.928 |
| 100 | 70.215 | 66.759 | 59.690 | 21.206 |
| 125 | 109.710 | 104.311 | 93.266 | 33.134 |
| 150 | 157.983 | 150.207 | 134.303 | 47.713 |
| 200 | 280.858 | 267.035 | 238.761 | 84.823 |
Calculated using densities of 8.94, 8.50, 7.60 and 2.70 g/cm3.
Sheet Theoretical Weight (kg per square metre)
| Thickness (mm) | Copper | Brass | Aluminium |
|---|---|---|---|
| 0.5 | 4.47 | 4.25 | 1.35 |
| 1 | 8.94 | 8.50 | 2.70 |
| 1.5 | 13.41 | 12.75 | 4.05 |
| 2 | 17.88 | 17.00 | 5.40 |
| 3 | 26.82 | 25.50 | 8.10 |
| 4 | 35.76 | 34.00 | 10.80 |
| 5 | 44.70 | 42.50 | 13.50 |
| 6 | 53.64 | 51.00 | 16.20 |
| 8 | 71.52 | 68.00 | 21.60 |
| 10 | 89.40 | 85.00 | 27.00 |
| 12 | 107.28 | 102.00 | 32.40 |
Applications
Power Plants
Busbars, conductors and electrical connections.
MEP & HVAC
Copper tubing and brass fittings for building services.
Manufacturing
Precision turned components and bushes.
Chemical Processing
Corrosion resistant parts for process equipment.
Infrastructure
Aluminium sections and fabrication work.
Water Treatment
Bronze and gunmetal pump and valve parts.
Ready to Discuss Your Project?
Get in touch with us today for premium industrial piping & metal solutions.